Home / Garden furniture / How to Repair Rattan Garden Furniture

How to Repair Rattan Garden Furniture

Rattan garden furniture is woven, so most damage is local: a strand works loose, a section of weave breaks, or a frame joint works free. Much of it can be repaired at home with simple tools and a little patience. This guide explains the common damage, what you need, and how to fix each one.

Summary Verdict

Most rattan repairs are small and local, so fix loose strands early, replace broken ones with matching weave, and check the frame before you start.

Best for

Sets with a sound frame and local weave damage, like a loose or broken strand.

Anyone comfortable with pliers, glue and a patient hour of weaving.

Watch out for

Pulling a loose strand out, which starts the weave unravelling.

Repairing a bent or rusted frame, which needs a workshop, not a toolbox.

Common damage and what causes it

The most common damage is a loose strand. It starts where the weave meets the frame, or where a chair arm rubs against a table, and the strand works free a little at a time. A broken strand is the next stage, usually caused by the same rubbing, or by a heavy knock. The weave can also sag where the frame underneath has bent, and the feet can wear down so the set rocks.

Frame damage is less common but more serious. A steel frame can rust where the coating is chipped, and rust weakens the tube until it bends. An aluminium frame can crack at a weld if it is overloaded. Cushions wear too, but that is a separate job. Before any repair, work out what caused the damage, because a repair that ignores the cause will fail the same way.

Tools and materials

You need a small set of tools: flat nose pliers, a craft knife or sharp scissors, a glue made for plastic, and a heat source like a hairdryer. Spare weave is the key material, and it should match the width, profile and colour of the original. Ask the maker or the retailer first, because many sell repair kits for their own sets. If that fails, a craft supplier or a specialist retailer may stock matching weave.

You may also need cable ties, small screws or rivets for the frame, and replacement feet or glides. A tube of clear sealant can help hold a tucked strand in place. Keep the work area clear and dry, and work in good light, because weaving is fiddly and a strand dropped on the grass is hard to find. Take a photo of the weave pattern before you start, so you can copy it.

Fixing a loose strand

A loose strand should be fixed as soon as you notice it, because it will unravel further if it is left. Push the strand back into place with your fingers or the pliers, following the same over and under pattern as the strands around it. Once it is back in place, put a small drop of glue for plastic under the end and hold it until it sets. A hairdryer on a low setting can help the glue set and can soften the strand so it bends without cracking.

Do not pull the loose strand out, even if it looks untidy. Pulling it will loosen the strands next to it, and the damage will spread. If the end is frayed, trim it neatly with the craft knife and tuck the cut end under the next strand. A repair that is tucked and glued will be almost invisible, and it will hold for a long time if the cause of the loosening is fixed too.

Pros

  • Loose strands are quick to fix if caught early
  • Spare weave and glue are cheap compared with a new set
  • A tucked repair is almost invisible once done

Cons

  • Matching the weave colour and width can be hard
  • Weaving is slow, fiddly work that needs patience
  • A repair will not hold if the frame underneath is bent

Replacing a broken strand

A broken strand needs replacing rather than gluing, because a glued break in the middle of a strand will fail again. Cut the broken strand out carefully, leaving the ends tucked under the neighbouring strands. Cut a new strand to length, allowing extra at each end for tucking in. Weave it through in the same over and under pattern, using the photo you took as a guide.

Tuck both ends under the nearest strands and glue them in place. If the new strand is stiff, warm it gently with a hairdryer so it bends without cracking. Work slowly, and check the tension as you go: the new strand should sit at the same tension as the strands around it, not tighter and not looser. A strand that is too tight will pull the weave out of shape, and one that is too loose will sag.

A loose strand left alone will unravel further, so fix it the week you notice it.

Frame, feet and cushion damage

If the set rocks or wobbles, check the frame before the weave. Tighten any bolts, and look for a bent tube or a cracked weld. A bent aluminium tube can sometimes be straightened gently, but a cracked weld needs welding, which is a workshop job. A rusted steel tube should be cleaned back to bright metal, treated and painted, but if the rust has eaten through the tube, the frame is finished.

Worn feet are an easy fix. Pull the old glide off and push a new one on, matching the size of the tube. If the feet are missing, the bare tube will scratch the patio and let water in, so replace them promptly. Cushion covers that are torn can be sewn or replaced, and foam that has gone flat can be replaced with new foam cut to size. These small jobs keep a set in use for years.

When repair is not worth it

Some damage is beyond home repair. A frame that is bent in several places, a steel tube rusted through, or a weave that is brittle and breaking in many places all point to a set at the end of its life. If the cost of spare weave, glue and new feet approaches the cost of a replacement chair, it is better to replace the chair and keep the rest of the set.

A set that has been repaired well can last for several more seasons, but it should be checked each spring. Look at the repaired strands, the frame joints and the feet, and fix anything loose before the season starts. The guide to rattan garden furniture explains what to look for when buying a new set, and the same checks apply when you are deciding whether a repair is worth doing.